최신 300-610 무료덤프 - Cisco Designing Cisco Data Center Infrastructure
A network engineer must design a Cisco HyperFlex solution based on these requirements:
* two clusters in the main data center consisting of five HyperFlex nodes
* one edge node tor the remote branch
* cluster nodes that use one rack unit of space
Which two devices should be used in the remote branch cluster for this design? (Choose two.)
* two clusters in the main data center consisting of five HyperFlex nodes
* one edge node tor the remote branch
* cluster nodes that use one rack unit of space
Which two devices should be used in the remote branch cluster for this design? (Choose two.)
정답: B,E
설명: (DumpTOP 회원만 볼 수 있음)
An engineer must build a VXLAN flood-and-learned network. The customer requires the solution to be based on the IETF documented practice in RFC 7348. The solution must use broadcast, unknown unicast, and multicast (BUM) and include the efficient BUM and short BUM replication modes that use only shared trees. Which technology meets these requirements?
정답: A
A network engineer needs to configure a high availability feature for a data center that uses a Cisco Nexus 7700 Series Switch that is configured with dual supervisors. The feature must meet these requirements:
* Network resilience must be ensured.
* Network instability for Layer 3 external routing protocols must be reduced.
* Neighbors must be notified when the control plane is restarting.
* Traffic must still be forwarded to peers while neighbor relationships arc restarting.
What should be used to meet these requirements?
* Network resilience must be ensured.
* Network instability for Layer 3 external routing protocols must be reduced.
* Neighbors must be notified when the control plane is restarting.
* Traffic must still be forwarded to peers while neighbor relationships arc restarting.
What should be used to meet these requirements?
정답: B
A network engineer is connecting a backup server to the given network The server has three available physical Ethernet interfaces - dual 1Gbps interfaces, plus a single 10Gbps interface - and all devices support virtual port channels The engineer must minimize backup time from hosts on the network, with a mandate for no single point of failure connectivity within the data center and the interfaces either active or passive Which deployment model must the engineer use?
A)
B)
C)
D)
A)
B)
C)
D)
정답: A
An engineer must design a Cisco UCS environment for a customer The design requires the most efficient use of available bandwidth with active-active uplinks The upstream Cisco Nexus 9000 Series Switch must automatically initiate the port-channel connectivity to the fabric interconnects Which configuration must the engineer choose to meet these requirements?
정답: C
설명: (DumpTOP 회원만 볼 수 있음)
A customer connects a high-speed Fibre Channel storage array to a Cisco MDS 9000 Series Switch using an 8 Gbps interface.
Which action guarantees line rate traffic processing on the interface?
Which action guarantees line rate traffic processing on the interface?
정답: A
A cloud provider deploys an infrastructure based on Cisco ACI Fabric, Cisco UCS, and Cisco HyperFlex Data Platform. The storage area network will be based on Cisco MDS 9000 Series Switches with Hyper-V, VMware, and KVM used as the virtualization platform. The requirement is to deploy the overall solution by using a robust automation and orchestration tool.
Which tool meets these requirements?
Which tool meets these requirements?
정답: B
An engineer must design a multitenant solution using Cisco 7709 switches. The solution must support separate routing instances, separate spanning tree domains, and separate firewalls for each tenant. Which solution meets these requirements?
정답: D
A network consultant proposes that the configuration of the Cisco UCS servers be based on service templates to facilitate the UCS infrastructure operation. The service profiles must remain connected to the template and be modified when the template settings are changed.
Which configuration meets these requirements?
Which configuration meets these requirements?
정답: C
Drag and drop the technologies from the left onto the correct descriptions on the right.
정답:
An ACI deployment must:
Which VRF configuration must be used?
Which VRF configuration must be used?
정답: B
A network architect wants to automate data center LAN configuration by use of Kubernetes, aligned with Cisco best practices for underlay and overlay provisioning The automation must be able to operate in high-availability mode with active/active operation between hosts in dual data centers. Which configuration approach must the architect choose?
정답: A
A SAN fabric is built between a pair of Cisco MDS 9000 Series Switches. The requirement is for the ISL to use the VSAN ID to toward traffic from multiple VSANs across the same physical link. Additionally, the Fibre Channel trace feature must be supported. Which ISL interface parameters are required to meet these requirements?
정답: A
The data center aggregation layer that uses IPv4 and IPv6 address space must act as a redundant Layer 3 gateway The solution must support a minimum of 240 virtual groups for an interface The data center aggregation layer hosts network devices from different vendors Which FHRP solution meets these requirements?
정답: C
To help automate the vHBA configuration process, a network engineer is configuring vHBA template pairs on UCS. The engineer is creating primary and secondary templates to define how vHBAs on a server connect to the SAN. Which fact about the template pair should the engineer consider for its potential impact on service?
정답: D
Which type fields can an engineer use to identify an iSCSI participant? (Choose two.)
정답: B,C
A network engineer designs a virtual network in a Cisco UCS Manager. The traffic must be explicitly forwarded from the vNIC on the server to a specific uplink Ethernet port on the Cisco fabric interconnect. Also, the server vNIC must use the same uplink Ethernet port after reboot. Finally, the design requires a OoS policy for remote direct memory access over converged Ethernet (RoCE v2). Which set of design features meets these requirements?
정답: A
Refer to the exhibit.
정답:
An engineer must deploy a SAN that meets these criteria:
* The upstream director switch must be configured to minimize the number of issued domain IDs
* The access switch must aggregate multiple locally connected ports not a single uplink that shares the same domain ID as the upstream switch.
Drag and drop the port types from the right onto the boxes on the left to create a SAN topology that meets these requirements Not all port types are used Port types are used more than once
An engineer configured the OSPF protocol in the vPC topology. During the catastrophic failure of one of the vPC the member switches, the traffic was routed to a black hole. This route was caused by the long convergence time caused by the delay of the of the vPC member switch reboot. After the failure, the engineer rebooted both switches, but the secondary switch powered on before the primary one. It caused all the vPCs to be shut down due to consistency-check violations. Which two features must be used to prevent these situations from happening in the future? (Choose two.)
정답: C,D
설명: (DumpTOP 회원만 볼 수 있음)
An engineer must logically partition two Cisco Nexus 7000 Series Switches into two environments called Test_39919596 and Production_59423879. The environments must use only F2-Series line cards and be limited to a maximum of 265 port-channels. Which Cisco Nexus feature must be used?
정답: D