최신 300-615 무료덤프 - Cisco Troubleshooting Cisco Data Center Infrastructure

문제1

Refer to the exhibit. The HSRP configuration in the exhibit fails to function. Which action resolves this issue?

A. Configure HSRP version 2.

B. Set the MTU to 1500 bytes.

C. Configure the same HSRP group on both devices.

D. Enable IP redirects.

정답: A

설명: (DumpTOP 회원만 볼 수 있음)

문제2

Refer to the exhibit. A blade that is connected to FI-A fails to boot from a SAN LUN. The boot policy is configured to boot by using vHBA0 as the SAN Primary. Which set of actions resolves the issue?

A. Change Adapter Policy to VMWare on vHBA0

B. Set VSAN to 11 in vHBA_SAN_

C. Change vHBA0 to VSAN 11 in Service Profile

D. Configure vHBA_SAN_A zone to VSAN 10

정답: C

문제3

Refer to the exhibit. An engineer troubleshoots the HSRP configuration and notes that the remote end uses HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues. Which action resolves the issue?

A. Set the local group number as 300 in the remote data center configuration

B. Run version 1 and version 2 HSRP on VLAN300 in the local data center.

C. Change the local group number to 255 or less and request that the remote data center matches the group member in its configuration.

D. Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the version to version 1.

정답: C

설명: (DumpTOP 회원만 볼 수 있음)

문제4

Refer to the exhibit. A network engineer is implementing a pair of Cisco Nexus 9000 Series Switches. During the OSPF configuration, the engineer discovers unstable routing in the network.
The investigation shows flapping routes after the new switches were introduced. Which set of actions resolves the issue?

A. Configure a new IP address on the Loopback interface for the OSPF process.
Clear the OSPF process

B. Configure a new IP address on the Ethernet interface toward the OSPF neighbor.
Clear the OSPF neighbor.

C. Configure a new IP address on the Ethernet interface toward the OSPF neighbor.
Clear the OSPF process.

D. Configure a new OSPF priority on the Ethernet interface toward the OSPF neighbor.
Clear the OSPF neighbor.

정답: D

문제5

Refer to the exhibit. An engineer troubleshoots an OSPF neighborship problem between Router R2 and Router R10. Which action resolves the problem?

A. Change router ID on Router R10

B. Resolve unicast reply from Router R2

C. Change area ID on Router R10

D. Resolve authentication type on Router R10

정답: B

문제6

A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager. Which set of steps resolves the issue?

A. 1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status
4) Reseat the affected IOM.

B. 1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status.
4) Reseat the affected IOM.

C. 1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status
4) Reseat the affected IOM.

D. 1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status.
4) Reseat the affected IOM.

정답: A

설명: (DumpTOP 회원만 볼 수 있음)

문제7

Refer to the exhibit. A web browser displays a "not secure" warning message when accessing the web interface of Cisco UCS Manager. Which action resolves the issue?

A. Use a supported version of UCS Manager.

B. Use the correct TCP port for HTTPS.

C. Use a supported web browser.

D. Load third-party certificate to UCS Manager.

정답: D

문제8

Refer to the exhibit. A network engineer configures an authentication domain through an LDAP provider on the Cisco UCS Manager for users from different companies to log into their respective organizations created in the UCS Manager. The engineer tests the configuration and notices that any user has login access to any organization in the UCS Manager. Which action should be taken to resolve the issue?

A. Configure the Filter field with sAMAccountName=$company

B. Configure the Filter field with the company

C. Configure the Attribute field with sAMAccountName=$company

D. Configure the Attribute field with the company

정답: A

문제9

Refer to the exhibit. A network engineer upgrades the firmware of a Cisco Fabric Interconnect from boot flash. During the process, the fabric interconnect reboots and displays the message shown in the exhibit. Which action resolves the issue?

A. Reload the switch and boot the kickstart image from the TFTP server

B. Reset the I/O module and install the firmware image from the boot flash

C. Remove the service pack and upgrade through the auto-install procedure

D. Boot the kickstart image from boot flash and load the system image

정답: A

문제10

An engineer must configure Linux hosts that are deployed on Cisco UCS B-Series Servers to boot from SAN.
The SAN boot policy is configured in Cisco UCS Manager, and the boot order is verified to be set as expected.
However, the Linux hosts fail to boot. Which action resolves the issue?

A. Delete and reconfigure the pWWN of the SAN boot target

B. Remove all of the local storage that is installed

C. Remove all of the ISO images that are mounted as a virtual CD-ROM

D. Delete and reconfigure the boot LUN

정답: B

문제11

Refer to the exhibit. Cisco UCS Manager is being upgraded using the Auto Install feature, but the FSM fails. Which action resolves the issue?

A. Upgrade the firmware of the infrastructure firmware by using the force option.

B. Acknowledge the primary fabric interconnect.

C. Remove the service pack from the subordinate fabric interconnect.

D. Clear the startup version of the default infrastructure pack.

정답: D

문제12

Refer to the exhibit. Users in the tech1 role are unable to create VLAN 99.
Which action do you take to resolve the issue?

A. Allow the tech1 role to access the layer2 configuration commands

B. Change rule 20 to permit access to the VLAN command.

C. Add VLAN 99 to the permit VLAN range.

D. Add a rule that permit VLAN configuration

정답: C

설명: (DumpTOP 회원만 볼 수 있음)

문제13

Refer to the exhibit. A network engineer must display the status of the vPC domain using the Python script and guest shell. The status of Cisco Nexus switches 1 and 2 must be displayed, but the code fails and displays the status of Cisco Nexus switches 0 and 1 instead. Which code resolves the issue?

A. for i in range(1,3): on line 4

B. for i in range(1-2): on line 4

C. print ('Show VPC On Switch', [i] + 1, '\n') on line 5

D. print ('Show VPC On Switch', i + 2, '\n') on line 5

정답: A

문제14

A network engineer finds an error that says, "BIOS failed power-on self-test." When the engineer checks the console, they discover that the Cisco UCS Blade firmware upgrade process stopped at the "Configuring and testing memory" stage.
Which set of actions resolves the issue?

A. 1. Add the CIMC firmware on a server.
2. Initialize the CIMC firmware on a server.

B. 1. Upgrade the firmware on an adapter.
2. Enable the firmware on an adapter.

C. 1. Update the BIOS firmware on a server.
2. Activate the BIOS firmware on a server

D. 1. Create a new host firmware package.
2. Assign the host firmware package to the service profile template.

정답: C

문제15

Refer to the exhibit. The LACP port channel fails between N9K-A and N9K-B. Which action resolves the issue?

A. Add the member interfaces to the port channel on N9K-B.

B. Add the member interfaces to the port channel on N9K-A.

C. Configure the port channel to be in active mode on N9K-B.

D. Configure the port channel to be in static mode on N9K-A.

정답: B

문제16

A network engineer must configure SNMP monitoring on the Cisco Nexus 5000 Series Switch.
The engineer issues the SNMP-server user testuser enforcePriv command but receives this message: "Unable to update CLI users database". Which change to permissions for testuser resolves the issue?

A. Add write permission.

B. Restrict read permission.

C. Add read permission.

D. Restrict write permission.

정답: A

문제17

Refer to the exhibit. A blade server on UCS-1 fails to boot from SAN. The PWWNs of the server and the target device are in the fabric login database of the N9K-1. Which set of actions resolves the issue?

A. Reset HBA adapter 1/2/1 to reinitiate FLOGI.

B. Configure zoning and activate the zone set.

C. Set fabric binding based on the initiator PWWN and target PWWN.

D. Define LUN masking on the storage array.

정답: D

최신 300-615 무료덤프 - Cisco Troubleshooting Cisco Data Center Infrastructure

우리와 연락하기

유용한 링크

최신 업데이트