최신 350-501 무료덤프 - Cisco Implementing and Operating Cisco Service Provider Network Core Technologies
Refer to the exihibit.
Refer to the exhibit. An Ethernet access provider is configuring routers PE-1 and PE-2 to provide E-Access EVPL service between UNI and ENNI. ENNI service multiplexing is based on 802.1ad tag 150, and service-multiplexed UNI is based on 802.1q tag 10. Which EFP configurations must the provider implement on PE-1 and PE-2 to establish end-to-end connectivity between CE-1 and CE-2?
Refer to the exhibit. An Ethernet access provider is configuring routers PE-1 and PE-2 to provide E-Access EVPL service between UNI and ENNI. ENNI service multiplexing is based on 802.1ad tag 150, and service-multiplexed UNI is based on 802.1q tag 10. Which EFP configurations must the provider implement on PE-1 and PE-2 to establish end-to-end connectivity between CE-1 and CE-2?
정답: B
설명: (DumpTOP 회원만 볼 수 있음)
Refer to the exihibit.
Refer to the exhibit. A network engineer with an employee ID 4379:43:595 is setting up an IS-IS network with these requirements:
Routes with a tag of 80 and IP prefixes other than 192.168.10.20/24 must be redistributed from Level 1 into Level 2.
Route leaking must be configured from Level 2 into the Level 1 domain for routes that are tagged with only 50 or 40.
Which configuration must be implemented on RB to meet the requirements?
Refer to the exhibit. A network engineer with an employee ID 4379:43:595 is setting up an IS-IS network with these requirements:
Routes with a tag of 80 and IP prefixes other than 192.168.10.20/24 must be redistributed from Level 1 into Level 2.
Route leaking must be configured from Level 2 into the Level 1 domain for routes that are tagged with only 50 or 40.
Which configuration must be implemented on RB to meet the requirements?
정답: A
설명: (DumpTOP 회원만 볼 수 있음)
A company is expanding its existing office space to a new floor of the building, and the networking team is installing a new set of switches. The new switches are running IGMPv2, and the engineers configured them for VLAN10 only. The rest of the existing network includes numerous Layer 2 switches in multiple other VLANs, all running IGMPv3. Which additional task must the team perform when deploying the new switches so that traffic is switched correctly through the entire network?
정답: A
Refer to the exhibit:
When implementing an LDP protocol, an engineer experienced an issue between two directly connected routers and noticed that no LDP neighbor exists for 1.1.1.1.
Which factor should be the reason for this situation?
When implementing an LDP protocol, an engineer experienced an issue between two directly connected routers and noticed that no LDP neighbor exists for 1.1.1.1.
Which factor should be the reason for this situation?
정답: B
설명: (DumpTOP 회원만 볼 수 있음)
An ISP Is Implementing end-to-end fault monitoring for a customer based on the IEEE 802.3ah standard. The solution must detect when 15 or more corrupted Ethernet packets arrive within 10 ms and stop propagating traffic through the ISP backbone network or to the customer side. Which configuration must the ISP engineer apply?
정답: D
In an EVPN operation, how does the PE determine and advertise Ethernet segment reachability?
정답: C
설명: (DumpTOP 회원만 볼 수 있음)
Drag and drop the technologies from the left onto the correct definitions on the right.
정답:
Which BGP attribute is used first when determining the best path?
정답: B
설명: (DumpTOP 회원만 볼 수 있음)
The engineering team at a large ISP has been alerted a customer network is experiencing high traffic congestion. After a discussion between the ISP and technical personnel at the customer site, the team agrees that traffic to the customer network that exceeds a specific threshold will be dropped. Which task must the engineer perform on the network to implement traffic policing changes?
정답: A
설명: (DumpTOP 회원만 볼 수 있음)
A network engineer must configure a router for Flexible NetFlow IPFIX export. The IP address of the destination server is 172.17.12.1. The source address must be set to the Loopback0 IPv4 address and exported packets must be set to DSCP CS3. The TTL must be 64 and the transport protocol must be set to UDP with destination port 4739. Which configuration must the engineer apply to the router?
정답: D
설명: (DumpTOP 회원만 볼 수 있음)
Refer to the exihibit.
Refer to the exhibit. EIGRP is running between routers R5 and R1, and OSPF is used in the rest of the network. Users in a network attached to router R3 need to access a server connected to R5. Which task must the engineer perform so that only the users attached to R3 are able to access the server, but no other network is shared to OSPF?
Refer to the exhibit. EIGRP is running between routers R5 and R1, and OSPF is used in the rest of the network. Users in a network attached to router R3 need to access a server connected to R5. Which task must the engineer perform so that only the users attached to R3 are able to access the server, but no other network is shared to OSPF?
정답: C
An engineer is trying to implement BGP in a multihomed architecture. What must the engineer configure to influence inbound path selection?
정답: D
설명: (DumpTOP 회원만 볼 수 있음)