최신 642-035 무료덤프 - Cisco Troubleshooting Cisco Data Center Unified Computing

문제1

You are attempting to install Microsoft Server 2008 R2 on a Fibre Channel LUN, but the installer does not see the LUN. You have used F6 to load the appropriate SCSI driver. What should your first troubleshooting step be?

A. Check the configuration of the vHBA in the service profile.

B. Validate zoning on the Fibre Channel switch.

C. Validate that the Fibre Channel uplink from the fabric interconnect is up.

D. Validate that the boot order is correct.

E. Email the SAN administrator to validate that your LUN is defined.

정답: A

문제2

HOTSPOT

정답:

문제3

You have an unresponsive blade server. You suspect that there is an issue with the current firmware. Which action do you take to reboot the server from the Cisco UCS Manager GUI?

A. Reset CIMC.

B. Recover the corrupt BIOS.

C. Reset BM

D. Reset the server.

정답: A

문제4

For a KVM session to be successful, which two of these need to be done? (Choose two.)

A. The Cisco IMC needs to be upgraded to the same version as the UCS Manager.

B. The Cisco IMC IP address needs to be in the same subnet as the management IP.

C. The Cisco IMC IP address needs to be assigned on the Admin tab.

D. The server needs to be fully discovered.

정답: C,D

문제5

Refer to the exhibit. A system administrator reviews the VIF paths and discovers an error. What is the cause of the error?

A. The switch that is connected the fabric interconnect has a port that is unavailable.

B. The server has no connection to the SAN.

C. The server is still booting over SAN.

D. The server has the VIC with errors and needed to make an RMA.

E. The server is still booting over iSCSI.

정답: E

문제6

Refer to the exhibit.

Which type of power policy is shown when referring to a Cisco UCS environment?

A. chassis

B. blade server

C. fabric interconnect

D. switch

E. global

정답: E

문제7

Refer to the exhibit. Which three statements are true based on the output of "show service-profile circuit server 1/3". (Choose three.)

A. vnic eth1 is pinned to port channel 6.

B. vnic eth0 is pinned to module 0 interface 1.

C. A LAN pin group is configured on vnic eth0.

D. vnic eth0 is pinned to port channel 1.

E. vnic eth1 is pinned to module 1 interface 6.

F. A LAN pin group is configured on vnic eth1.

정답: D,E,F

문제8

During the installation of Windows 2008 64-bit operating system on a Cisco UCS server, the RAID controller is not found. What is the cause of the problem?

A. The LSI drivers are not bundled and need to be loaded by clicking the Load Driver option to point to the correct drivers.

B. The LSI option ROM needs to be configured by pressing Ctrl-H during post.

C. Windows 2008 64-bit operating system is not supported on Cisco UCS servers.

D. The Cisco IMC firmware needs to be updated.

정답: A

문제9

Which three components are updated using the Host Upgrade Utility? (Choose three.)

A. BIOS

B. Array Controller

C. Cisco IMC

D. Network Adapter(s)

E. UCSM

F. Drive Firmware

G. LOM port

정답: A,C,D

문제10

What is the reason that no C-Series servers can access Fibre Channel storage from this Cisco Nexus 554SUP switch?

A. Zoning mode mis-match with the MDS 9124

B. None of the virtual fibre channel interfaces are configured

C. VSAN mis-match on Fibre Channel interfaces

D. There are no active Fibre Channel interfaces

정답: A

최신 642-035 무료덤프 - Cisco Troubleshooting Cisco Data Center Unified Computing

우리와 연락하기

유용한 링크

최신 업데이트