최신 CWDP-304 무료덤프 - CWNP Certified Wireless Design Professional
A wireless engineer from your company performed a site survey in an office building where a wireless network extension was needed. He reports that while performing a Layer 1 sweep near a meeting room full of people, he detected RF activity with a very low duty cycle. He is unsure how to interpret what he recorded to determine its impact on a future Wi-Fi network.
What is true about this RF environment and its potential impact on the WLAN?
What is true about this RF environment and its potential impact on the WLAN?
정답: C
In a large enterprise (5000+ wireless users), by what would NOT be a recommended method by which IP addresses and VLANs are assigned to different clients associated to the same AP?
정답: B
What architecture suffers the biggest limitation for sharing control information across APs?
Response:
Response:
정답: B
In 802.11, clients are required to be calibrated for RSSI and SNR reporting to:
정답: B
The installation crew for your WLAN project wants to install a few APs to locations nearby the ones specified in the RF design document. What next step should occur?
Response:
Response:
정답: B
When installing APs on high ceilings, what should be the most common PPE to be used?
정답: D
During a post-validation assessment, you have configured a client for 802.1X/EAP but it is not passing authentication. Which areas should you check in the WLAN configuration?
Response:
Response:
정답: C
When implementing WLAN security according to common best practices, what feature should be enabled when configuring an EAP type?
정답: D
What commonly causes a client-to-AP link imbalance?
정답: C
What differences exist between VLANs in wireless and wired domains?
Response:
Response:
정답: B
What should you do during the design process of a point to point bridge link to minimize CCI and ACl?
정답: C
Why should band steering algorithms allow stations to connect to the 2.4 GHz band after some number of ignored Probe Requests?
정답: D
What commonly used item can help lo prevent back pain during lengthy site surveys?
정답: D
You have performed a validation site survey after deploying a WLAN infrastructure that is an All-Wireless- Office. One specific application of your customer is experiencing delay when using the application after moving from wired connectivity. After your validation, you realized that all APs are using 80 MHz channel- widths instead of 20 MHz on the 5 GHz band, as it was designed. What can be done to resolve the delay on this application?
정답: D
What document should be created that provides instructions for install technicians to mount and configure APs?
정답: B
What metric implements the simplest algorithm and lowest accuracy in networks requiring locations?
Response:
Response:
정답: B
During lunch time in the break room of a company, Wi-Fi connectivity on the 2.4 GHz band is intermittent.
Every other time of the day, it works fine.
What's the likely cause of this issue?
Every other time of the day, it works fine.
What's the likely cause of this issue?
정답: D
You are validating association capabilities from clients to an 802.1X/EAP secure SSID. The RADIUS server's IP address is 10.100.50.25 and the default RADIUS authentication port is used. When testing them, none of the clients are able to associate to the SSID. Troubleshooting the WLAN infrastructure, you found out that the server is up and the RADIUS service is up as well, but the authenticator is not able to communicate properly with the server. What's your next troubleshooting step?
정답: A
You desire to achieve a 450 Mbps MCS. What 802.11n features (from the numbered list below) are required?
1. Frame aggregation
2. Short GI
3. 40 MHz channels
4. 2 spatial streams
5. 3 spatial streams
6. Transmit beamforming (TxBF)
1. Frame aggregation
2. Short GI
3. 40 MHz channels
4. 2 spatial streams
5. 3 spatial streams
6. Transmit beamforming (TxBF)
정답: D
When preparing a floor plan graphic for use in predictive and manual site surveying, what calibration method will lead to the most accurate and reliable RF data?
정답: D